|
Motorola RAZR, RIZR, Z8 mini-USB Charger specification users reports and reviews |
| Date | User opinion | Comment | Content Revision |
Approved by moderator? |
|---|---|---|---|---|
| ERROR FIXED | X - R-200KOhm to GND PIN 2 and 3 short is corect for charging | APPROVED | ||
| CORRECT | The pin outs were correct. The description of which pins are shorted to get the phone into charge mode was also correct | APPROVED | ||
| ERROR FIXED | it"s 200k or 220k | APPROVED | ||
| CORRECT | correct | APPROVED | ||
| CORRECT | APPROVED | |||
| INCORRECT | in the corrected section the pins for charging are marked as corrected but the text and table are still wrong, see http://krhainos.tk/motoplug.jpg for details | APPROVED | ||
| CORRECT | APPROVED | |||
| CORRECT | Confirmed via resistance testing and also via attempting charge a RAZR via a normal USB A - USB mini cable from a USB solar panel with negative results. Creating a cable from Motorolas original wall chargers USB mini connector and a regular USB A cable allows it to charge from a USB solar panel. | APPROVED | ||
| CORRECT | Confirmed working with 220k resistor. D- can be connected before or after the resistor without any negative effect. | APPROVED | ||
| CORRECT | I opened the AC charger while soldering a broken wire. I was able to verify the connections (pin1: +5VDC, pin4: GND ), and the value of the resistor (200K) between pin4 and pinX. After soldering the broken wire, I connected to the cell phone and started recharging without any problems. I also took some pics to save with the documentation. | APPROVED | ||
| CORRECT | APPROVED | |||
| CORRECT | APPROVED | |||
| INCORRECT | The directions are mostly correct. I found that pin 3 did need to be connected to x and 2 and the wire absolutely needed to be continuous to both ends of the cable. You can see a picture of the completed circut on the breadboard I used at the link below. Ill probably solder it all into a compact cable. I tried to diagram it in text also, but I worry that it will get formated strange when I hit submit. phoneMini-USB-B----- | APPROVED | ||
| INCORRECT | The new moto chargers (p/n: SPN5185B) came with Moto Q/Q9/V195 have pin 2 and pin 3 shorted together, pin x and pin 5 has 200K Ohm resistor across. Pin 2 and pin x are **NOT** shorted. | APPROVED | ||
| 2009-03-29 10:34:33 | CORRECT | rev. 7 | APPROVED | |
| 2009-06-25 02:52:21 | CORRECT | rev. 9 | APPROVED | |
| 2011-12-09 23:37:56 | CORRECT | rev. 12 | APPROVED |
| Date | Author | Content Revision |
Comment |
|---|---|---|---|
| 2008-08-21 21:55:07 | Butch | rev. 4 | The RAZR V3 charge strategy didn't work with my MOTORIZR Z6tv so I took it upon myself to probe it out . |
| 2008-09-09 14:48:13 | Andre Quirion | rev. 4 | I've took 3h to figure out my wiring wasn't working as it should be... and this is the result of my "strugling" |
| 2008-11-27 22:10:05 | Eric | rev. 6 | |
| 2009-01-03 22:18:39 | kaputnik | rev. 6 | added V3x details |
| 2009-05-13 22:04:11 | int_true | rev. 7 | |
| 2009-05-13 22:07:15 | Alex | rev. 7 | |
| 2009-06-14 22:20:31 | FX-Pain | rev. 9 | |
| 2009-06-29 21:47:29 | Tom Maneiro | rev. 9 | |
| 2010-01-06 23:21:54 | Jiri Naprstek | rev. 11 | Updated for V360 |
| 2010-02-27 21:56:39 | Steve | rev. 11 | |
| 2010-11-30 21:46:37 | Ron | rev. 12 | |
| 2010-11-30 21:46:49 | Ron | rev. 12 |
Pinouts.ru > Pinout of Motorola RAZR V3 mini-USB Charger and layout of 5 pin mini-USB plug connector |
should be correct |